Check Local Availability
check your local store, for in store pickup
check your local store, for in store pickup
check your local store, for in store pickup
Until about a year ago, my family cottage was falling into disrepair. My grandfather built the place with his bare hands, and watching the place crumbling at the foundations due to neglect was heart-wrenching. In order to correct the problem, my son and I took matters into our own hands. We packed some tools into the old pickup truck and drove the two hours and change to the cottage. Having taken a few days off work, we both had time to make some initial home improvements.
It wasn’t until several hours into the task that I realized I was getting dehydrated. Walking into the kitchen and turning on the tap, I found – much to my dismay – that a foul smelling, discolored liquid began coursing into the sink. This substance didn’t resemble any water I’d ever seen or tasted in the past, and I knew it was time to pull out my special plumbing tools and go to work. It seemed like for every two steps forward we took one back, but after a couple of weeks we finally got the job done.
Cleaning a hand saw isn’t very difficult, although it is messy. Being prepared with the proper equipment and selecting a place with good ventilation will help make the job easier.
All and any of your power tools need care as well, let’s get started on hand saws for now.
Next, for cleaning your hand saw, gather the following materials:
o A thin-bladed screwdriver (only needed if you are removing the handle)
o Mineral spirits
o A razor blade with a safe razor blade holder
o Silicon carbide sandpaper
o Boiled linseed oil
o Steel wool
o Paper towels
o Rags
o Paste wax
o Protective gloves
CAUTION: This is a very important safety issue. Mineral spirits, boiled linseed oil, paper towels and rags make a dangerous combination that can spontaneously combust if left unattended in a pile. Proper precautions should be taken to dispose of these items after use. Rags soaked in linseed oil should be laid out flat outdoors away from any structures to dry. When completely dry, they may be put in the trash. Store rags soaked in mineral spirits in a plastic bag away from all structures until dry before disposing of them. Do not use mineral spirits near an open flame, as the vapor can catch fire. Even the pilot light on your furnace or hot water heater may be enough to ignite the vapors. Mineral spirits can also cause nerve damage if used for a prolonged period or in a confined space. Make sure you have good ventilation and that you are not using the mineral spirits for long periods of time. If you don’t feel comfortable working with these hazardous materials, you may want to hire this job out. Safety first!
Now we’re ready to begin.
If you need to remove the handle, use a proper-fitting screwdriver. Be sure to place the screws somewhere secure where they won’t get misplaced. If the saw is very rusty, it may take a bit of effort to pull off the handle.
Once you’ve removed the handle, place the saw blade on a board or other flat surface. Use the razor blade to scrape off rust, dirt, wax or other crud that has built up on the surface. Work from the handle end towards the tip of the saw. Repeat the process on the other side.
Now that any loose debris has been removed apply a small amount of mineral spirits to the saw blade. Take a small square of the silicon carbide sandpaper and apply it to the blade using the mineral spirits as a lubricant. Move the sandpaper along the length of the blade, not back and forth from the teeth to the back. When you’re done, wipe off any excess spirits with paper towels. Repeat on the other side then set the blade aside to dry.
Use the razor to scrape any build-up off of the handle. Finish with steel wool. If the handle looks dry, use a rag to apply a small amount of boiled linseed oil. Make sure all surfaces are well-coated. Remove any excess oil with a clean rag. The handle should be completely dry in a couple of days.
Wipe down the dry hand saw blade with a rag to remove any residue, and apply some paste wax with a clean rag to protect the blade from future rust. Let the wax dry for ten minutes, then buff off any excess. Reassemble the handle when it has fully dried.
Foreclosures to persist
According to authors at the Federal Reserve Bank of Cleveland, the nation’s high foreclosure rate is likely to persist. The Fed article looks at the changes in foreclosure and unemployment rates across states, noting the differences in the timing of the movements. The conjecture that the high foreclosure rate will persist is based in part on the observation that states that experienced boom-bust housing cycles in the past (Texas, Oklahoma, Massachusetts and California) had elevated foreclosure starts for years after the peak in foreclosure starts and inventory. These previous boom-bust cycles “were small in comparison to the current cycle,” the article said. While the recession has left deep scars in the housing and labor markets — with the unemployment rate doubling and the foreclosure start rate roughly tripling — the timing of the movements differs over the cycle, according to the abstract, written by the vice president at the Federal Reserve Bank of Cleveland, and K.F., a research assistant.
In So-Cal every Wednesday morning there is a short sale workshop open to the public, allowing homeowners, agents, brokers or investors the opportunity to see and participate in how and why this has been changing communities across our nation. Join us this week or any week for a fulfilling chance at making a difference in the lives of others.
If you have any kind of prescription medication or otherwise potentially harmful products in your bathroom, it’s a good idea to keep all these products up high and out of the reach of small children. Kids, after all, are curious. And they always seem to have a way of finding the one thing they’re not supposed to have. That’s why “out of sight, out of mind” is a good tactic to take with all your dangerous bathroom products.
All you have to do is invest in some DIY cabinets. Especially if the cabinets aren’t clear, it will reduce the likelihood of anyone getting a hold of something they shouldn’t. Make sure these cabinets are up high enough that young children can’t reach them. These cabinets, of course, won’t be a safeguard against older children, but they can prove a simple and effective deterrent for your youngest.
A hand saw is one of the more basic tools, so you may not have given much thought to the proper way to use one. However, like other hand and power tools, using proper form and technique with a hand saw is important for your safety as well as achieving your desired result.
First and foremost, reading the documentation packaged with the saw is advised. All hand saws are not the same, so following the recommendations from the manufacturer will help you both use the saw properly and protect yourself. Hand saws come in different types that are designed for various purposes, so be sure you are using the right kind of saw for the task at hand. For instance, some saws are designed to cut with the grain, while others are designed for cutting against the grain.
Ensure your saw blade is sharp and clean before you begin. The first step to using a hand saw – determining exactly where the cut will be made – begins before you pick up the saw. Create a line to guide your cut, double checking that your measurements and angles are correct. Also ensure that the surface to be cut is stable.
Start sawing slightly to the outside of the line to account for the width of the blade. Hold the saw such that your wrist, shoulder and the handle of the saw are lined up, and you are not sawing at an angle that feels unnatural. Professionals generally advise holding a hand saw with all of the fingers except the pointer, which should be straight and pointed in the direction of the cut. But, be sure to check the documentation to ensure that you are holding the saw according to recommendations. Remember that cutting should be done on the down stroke. Apply pressure to the saw as you push downward on the cut, but release pressure as you pull the saw back toward yourself. Getting into a steady rhythm as you saw will help you achieve the cleanest cut.
If you are inexperienced with hand saws, you may want to practice cutting on a scrap piece of wood before you move on to the real cut. It bears repeating that all saws are not the same, so be sure to read the documentation outlining the proper use of your fine hand saw.